Search results for " Power electronics"
showing 10 items of 10 documents
Analytical Investigation and Control System Set-up of Medium Scale PV Plants for Power Flow Management
2012
In the field of photovoltaic (PV) plants and energy conversion from renewable sources, a large part of the technical literature is more devoted to practical aspects (new solar cells, electrically driven PV panels, safety, reduction of parasitic currents, etc.) than to theoretical investigations. Despite this tendency, this paper presents a mathematical analysis of a medium scale photovoltaic power generation system connected to the distribution network and of its control system. In such a system, the conversion stage is unique due to the absence of a boost chopper. The conducted analysis leads to the interesting conclusion that the inverter used in the plant presents two degrees of freedom,…
A photovoltaic system suitable for the battery pack charging of an electrically power assisted velocipede
2012
The paper describes the designing, sizing, realization and setting up of a complete system suitable for the management of an electrically power assisted velocipede using a photovoltaic module for the charging of the batteries. In the work an overview on the sustainable mobility needs and on the commercial electrically power assisted velocipedes is presented and the "Ecolapa" prototype, set up in the SDELab laboratory of Palermo University, is precisely described underlining the designing, implementation and setting up phases of the photovoltaic charging system settled up on the velocipede. Moreover tests oriented on the setting up of the whole system and validation tests on the prototype ar…
Vircator Technologies Comparison and Novel Anode Analysis
2021
High Power Microwave (HPM) sources are widely used as signal sources in radar, jammer, and Counter Improvised Explosive Devices (CIED). Such devices usually are heavy and bulky, characteristics that are in conflict with the small weight and power (SWaP) approach so that it is practically impossible to mount such HPMs on several platforms with reduced spaces (e.g., avionic, UAVs). During the last century, several devices have been proposed, all of them heavy due to the components that they need such as the magnetic material of the Magnetron, Klystron, or Gyrotron. Considering the HPM sources for pulsed applications, the VIRtual CAThode oscillatOR (Vircator) represents the best candidate due …
Comprehensive Analytical Investigation for PV Plants and Their Control System with Reduced Power Electronics Equipments
2012
This paper presents a comprehensive analysis of a power generation system from PV source and it control system with a reduced power equipments connected with a power AC grid. The absence of the boost chopper as an actuator for Maximum Power Point Tracking concurs to make the system more reliable, affordable and moreover cheaper respect to a traditional one in which the boost chopper is used. The mathematical analysis exposed in the paper shows as a three phase inverter has two degrees of freedom allowing the simultaneous MPPT control and the synchronization with the power grid. The analysis also shows the way to determine the duty cycle of the inverter to deliver active power, and eventuall…
Comparison between SiC and GaN switching devices in fast-recharging systems for electric vehicles
2023
Recently, the improvement of the semiconductor devices to achieve higher efficiency and higher power density has risen to interest. Si carbide and gallium nitride offer faster switching frequency and lower losses; however, the knowledge of the behaviour of these devices is not mature. In this paper, a system for fast charging of batteries for electric vehicles based on an isolated DC-DC converter equipped with both SiC and GaN devices is presented and an interesting experimental comparison among these two technologies will be given in terms of dynamic performances, electromagnetic compatibility, stability, efficiency, and so on.
A wireless battery charger architecture for consumer electronics
2012
In this paper, an innovative design of a wireless battery charger for portable electronic devices is proposed. The wireless power transfer is implemented through the magnetic coupling between a power transmitter, which is connected to the grid, and a power receiver, which is integrated inside the load device. An innovative receiver architecture which heavily improves the power conversion efficiency is presented. The proposed solution is standard compliant and suitable for IC implementation. A comparison between a conventional and the proposed receiver architectures is carried out by SPICE simulations. As shown by simulation results, a power efficiency increase by 40% is provided by the prop…
Design and Modeling of an Interleaving Boost Converter with Quasi-Saturated Inductors for Electric Vehicles
2020
This paper is focused on the analysis and modeling of DC-DC boost converters in interleaving configuration exploiting inductors in the quasi-saturation region. The converter is designed to optimize the power density by minimizing the size of the inductors. A simulation study for electric vehicle applications is conducted analyzing the effects of duty cycle and temperature variation on the ripple of the input current giving, moreover, information on the performances and dynamics of the converter for further implementation and optimizations.
A digital control technique for high-performances DC-DC converters
2008
Experimental test on a fuel cell-supercapacitor hybrid power supply for a digital still camera
2009
Development of bidirectional dc-dc converters for hybrid power sources - Final Report
2018
A Bidirectional Isolated Full-Bridge Converter was designed, prototyped and tested. The device is intended to interface a Bank of Supercapacitors with a battery-powered bus, in order to boost the capability of supplying large power peaks. The converter was based on the Isolated Dual Active Bridge configuration. When driven by an external control voltage, it is capable of generating in both directions a train of current pulses, with 2kW peak power, for any battery voltage in the range 24-32V and for any supercapacitor voltage in the range 35-70V. Worst-case battery current was 70A. Pulse duration was 100ms with 50% duty cycle and 1 ms rise time.